PSI to Torr Converter

PSI to Torr conversion table

How to convert PSI to torr

Torr = PSI × 51.714933. For example, 2 psi = 103.429865 Torr. Type a value in either box above: the other one updates instantly, both ways.

What is a psi?

PSI (pounds per square inch) is the US unit of pressure for tires and air compressors; 1 psi ≈ 6.895 kPa.

What is a torr?

A torr is 1/760 of a standard atmosphere, about 133.32 Pa, used in vacuum work.

Which number belongs in the psi input?

Enter the numerical quantity measured in psi, leaving the psi symbol in the label rather than inside the input. The second field represents torr and uses Torr. Both fields can be edited, but each has its own direction of conversion. Decide which quantity you know before typing. Decimal values are allowed; a mixed fraction or a number followed by descriptive text is not a numeric entry. Use the decimal separator accepted by your browser's number field and avoid pasted thousands separators when a value could be interpreted ambiguously.

How is the conversion calculated?

One psi unit represents 6894.75729316836 reference units, and one torr unit represents 133.322368421053 reference units. First multiply the input by 6894.75729316836 to reach the family reference quantity. Then divide by 133.322368421053 to express that quantity in torr. Combining the two steps gives the factor 51.7149325715071. The direction matters: this factor belongs to psi going to torr, rather than the other way round.

How can I check the intermediate calculation?

For a second worked example, begin with 2.5 psi. Multiplying by the source reference factor gives 17236.8932329209 reference units. Dividing that intermediate quantity by 133.322368421053 gives 129.287331428768 Torr. This two-step route is useful when you want to compare a spreadsheet with a hand calculation. Do not round the intermediate quantity before dividing: a small reference value can carry meaningful digits even when its short display looks close to zero. The reference quantity is not an extra measurement to add; it is the same measurement expressed temporarily on the common scale.

Can I combine values before converting?

If you have two separate quantities of 2.5 psi and 5 psi, combine them as 7.5 psi before converting. Their destination quantities are 129.287331428768 Torr and 258.574662857535 Torr; their sum agrees with 387.861994286303 Torr up to floating-point rounding. This works because a fixed factor distributes over addition. Bring mixed source units to one common unit first, and retain unrounded values when comparing totals. For an average, use the same weighting rule before and after conversion. A unit conversion does not decide whether two underlying quantities should be added or weighted equally in your particular application.

Worked values and a direction check

For 7.5 psi, the calculation is 7.5 × 51.7149325715071 = 387.861994286303 Torr. If the input doubles to 15.0 psi, the result doubles to 775.723988572606 Torr. Zero converts to zero. These relationships follow from multiplication by a fixed factor. They are useful checks when transcribing a reading or building a spreadsheet formula.

What conventions apply to this family?

Pressure factors refer to pascals. A bar is 100000 pascals, a kilopascal is 1000 pascals, and a standard atmosphere is 101325 pascals. Torr and millimeters of mercury have close but separately defined factors in this implementation. Gauge pressure and absolute pressure are two different reference conventions. A unit conversion preserves whichever convention the source used; it does not add atmospheric pressure. Record whether your instrument reads gauge or absolute values before comparing measurements. A negative gauge reading can describe pressure below its reference, but that does not make a negative absolute pressure physically meaningful. Changing the unit also cannot calibrate a sensor or compensate for temperature.

How much precision should I keep?

The displayed answer is a readable representation of a floating-point calculation. Very large or very small results may appear in scientific notation: the exponent indicates how many places to move the decimal point, rather than another unit. A short displayed factor can hide digits used internally. Use the full conversion expression for a spreadsheet instead of repeatedly multiplying by a rounded answer copied from the table. Round once, at the end, to the resolution your measurement supports. Extra digits in a conversion cannot improve the precision of a ruler, sensor, product label or original estimate.

How can I check a value before reusing it?

Keep both the source quantity and its psi unit beside the answer in Torr. Use the reverse field or the Swap link to check that converting back approaches the original number. Small differences after copying a rounded answer are expected; a large difference suggests a wrong direction, wrong family, or missing decimal place. Check the order of magnitude as well as the digits. Converting to a smaller unit usually produces a larger count for fixed-factor families, while temperature offsets need their own reference-point checks. An inverse check establishes consistency of the arithmetic, not accuracy of the original measurement.