Millimeters of mercury to PSI conversion table
| Millimeters of mercury | PSI |
|---|---|
| 1 mmHg | 0.0193367775 psi |
| 2 mmHg | 0.0386735549 psi |
| 5 mmHg | 0.0966838873 psi |
| 10 mmHg | 0.1933677746 psi |
| 25 mmHg | 0.4834194365 psi |
| 50 mmHg | 0.966838873 psi |
| 100 mmHg | 1.933678 psi |
How to convert millimeters of mercury to PSI
PSI = Millimeters of mercury × 0.0193367775. For example, 2 mmHg = 0.0386735549 psi. Type a value in either box above: the other one updates instantly, both ways.
What is a millimeter of mercury?
A millimeter of mercury (mmHg) is about 133.32 Pa, the unit for blood pressure readings.
What is a psi?
PSI (pounds per square inch) is the US unit of pressure for tires and air compressors; 1 psi ≈ 6.895 kPa.
Which number belongs in the millimeters of mercury input?
Enter the numerical quantity measured in millimeters of mercury, leaving the mmHg symbol in the label rather than inside the input. The second field represents psi and uses psi. Both fields can be edited, but each has its own direction of conversion. Decide which quantity you know before typing. Decimal values are allowed; a mixed fraction or a number followed by descriptive text is not a numeric entry. Use the decimal separator accepted by your browser's number field and avoid pasted thousands separators when a value could be interpreted ambiguously.
How is the conversion calculated?
One millimeters of mercury unit represents 133.322387415 reference units, and one psi unit represents 6894.75729316836 reference units. First multiply the input by 133.322387415 to reach the family reference quantity. Then divide by 6894.75729316836 to express that quantity in psi. Combining the two steps gives the factor 0.0193367774594621. The direction matters: this factor belongs to millimeters of mercury going to psi, rather than the other way round.
How can I check the intermediate calculation?
For a second worked example, begin with 2.5 mmHg. Multiplying by the source reference factor gives 333.3059685375 reference units. Dividing that intermediate quantity by 6894.75729316836 gives 0.0483419436486553 psi. This two-step route is useful when you want to compare a spreadsheet with a hand calculation. Do not round the intermediate quantity before dividing: a small reference value can carry meaningful digits even when its short display looks close to zero. The reference quantity is not an extra measurement to add; it is the same measurement expressed temporarily on the common scale.
Can I combine values before converting?
If you have two separate quantities of 2.5 mmHg and 5 mmHg, combine them as 7.5 mmHg before converting. Their destination quantities are 0.0483419436486553 psi and 0.0966838872973106 psi; their sum agrees with 0.145025830945966 psi up to floating-point rounding. This works because a fixed factor distributes over addition. Bring mixed source units to one common unit first, and retain unrounded values when comparing totals. For an average, use the same weighting rule before and after conversion. A unit conversion does not decide whether two underlying quantities should be added or weighted equally in your particular application.
Worked values and a direction check
For 7.5 mmHg, the calculation is 7.5 × 0.0193367774594621 = 0.145025830945966 psi. If the input doubles to 15.0 mmHg, the result doubles to 0.290051661891932 psi. Zero converts to zero. These relationships follow from multiplication by a fixed factor. They are useful checks when transcribing a reading or building a spreadsheet formula.
What conventions apply to this family?
Pressure factors refer to pascals. A bar is 100000 pascals, a kilopascal is 1000 pascals, and a standard atmosphere is 101325 pascals. Torr and millimeters of mercury have close but separately defined factors in this implementation. Gauge pressure and absolute pressure are two different reference conventions. A unit conversion preserves whichever convention the source used; it does not add atmospheric pressure. Record whether your instrument reads gauge or absolute values before comparing measurements. A negative gauge reading can describe pressure below its reference, but that does not make a negative absolute pressure physically meaningful. Changing the unit also cannot calibrate a sensor or compensate for temperature.
How much precision should I keep?
The displayed answer is a readable representation of a floating-point calculation. Very large or very small results may appear in scientific notation: the exponent indicates how many places to move the decimal point, rather than another unit. A short displayed factor can hide digits used internally. Use the full conversion expression for a spreadsheet instead of repeatedly multiplying by a rounded answer copied from the table. Round once, at the end, to the resolution your measurement supports. Extra digits in a conversion cannot improve the precision of a ruler, sensor, product label or original estimate.
How can I check a value before reusing it?
Keep both the source quantity and its mmHg unit beside the answer in psi. Use the reverse field or the Swap link to check that converting back approaches the original number. Small differences after copying a rounded answer are expected; a large difference suggests a wrong direction, wrong family, or missing decimal place. Check the order of magnitude as well as the digits. Converting to a smaller unit usually produces a larger count for fixed-factor families, while temperature offsets need their own reference-point checks. An inverse check establishes consistency of the arithmetic, not accuracy of the original measurement.
How do I convert millimeters of mercury to PSI?
Use the formula PSI = Millimeters of mercury × 0.0193367775. Type a value in the millimeters of mercury box and the result appears instantly.
How many PSI are in 1 millimeter of mercury?
1 mmHg = 0.0193367775 psi.
Is this converter free and private?
Yes. It is free, needs no sign-up, and the calculation runs in your browser: nothing is sent to a server.
Is this gauge or absolute pressure?
The conversion factor is the same for both. Tire gauges show gauge pressure (above the air around you); add about 14.7 psi or 1.013 bar to get absolute pressure.